LINEA DE CONSULTAS ABIERTA POR WHATSAPP AL 672.03.24.48 - HORARIO DE TIENDA FISICA: LUNES A VIERNES DE 16:00 A 20:00H
ULTIMAS NOVEDADES COVID19: DEBIDO AL EMPEORAMIENTO DE LA PANDEMIA, CIERRE DE FRONTERAS Y AL BREXIT ALGUNOS PEDIDOS PODRIAN SUFRIR DEMORAS
NO SE ADMITIRAN RECLAMACIONES NI CANCELACIONES DE PEDIDOS POR DEMORAS DE ESTA NATURALEZA AJENAS A NUESTRA VOLUNTAD

Notas Fabricante ST Suspension

0 = Technical-certificate not available on the day this catalogue was printed. Please check status with us.
1 = These spring sets can be used only with shortened shock absorbers! We recommend our Weitec sport shock absorbers. See application list for front and rear shock absorbers.
2 = Not for station wagon models (Estate/ Avant/ Turnier/ Variant/ T-modell...).
3 = Excluding models with 4 wheel steering.
4 = Excluding four wheel drive models.
6 = Not for vehicles with electronic damper control.
6a = Excluding models with electronic dampfer control. Use our spring sets please.
7 = If necessary, please exchange the front bump stops with the original ones (part number 1K0412303F)
8 = Excluding 16V/20V/24V and RSI.
9 = Spring kit consists of 2 front springs only.
10 = Not for cars with Audi magnetic ride
11 = Excluding models with automatic level control, or automatic level system can be adjusted in accordance.
11a = Complete suspension kits are excluding models with automatic level control, please use our springset.
14 = For vehicles with series sports suspension please use our complete suspension kit only.
16 = Excluding vehicles with series sports suspension.
18 = Spring kit includes only 2 rear springs.
19 = Excluding V-Tec models.
21 = Not for vehicles with gas-powered engines.
25 = No German Certificate will be delivered. Only a material certificate will be supplied.
27 = The front indicator lights on these vehicles must be relocated or replaced. These can be acquired from the manufacturer under order number 46226698.
30 = The quoted lowering can vary due to different original rubber springseats. Max lowering can be achieved by using single point rubber seats. Lowering can be adjusted by using different rubbers.
31 = Listed lowering can vary up to +/- 25 mm due to different model weights.
32 = VR6 only without air conditioning.
37 = The mentioned lowering rate may vary. The vehicles are delivered from factory with different lower spring rubber pads at the rear axle. The maximum lowering is achieved by using the spring rubber pads without indentation. The lowering rate can be varied accordingly by using spring pads with one or two indentations (the rubbers are only available in the original).
39 = Excluding GTI/GLI/GTE/GLE/GSI.
40 = Front axle height adjustable, rear axle consists of lowered sports springs and sports dampers.
41 = Front axle height adjustable, rear axle adjustable sports dampers. Height adjustment is by Torsion bar.
42 = In combination with original wheels and tyres, wheelspacers might be necessary.
44 = Only for models with 45 mm strut diameter outside (Can also be measured when fitted on the vehicle).
45 = Only for models with 51 mm strut diameter outside (Can also be measured when fitted on the vehicle).
46 = Special kit for vehicles with level control. The height will be adapted by adjusting the levelling sensor.
48 = The maximum axle load is reduced to the amount mentioned in brackets.
52 = Excluding convertible.
54 = Excluding "full options" models.
55 = Only "full options" models.
57 = Excluding automatic gear box.
59 = Only for models with series sports suspension.
65 = Excluding models with pneumatic suspension.
66 = Not avlailable for fun/cross models or models with rough road packages.
70 = We advise checking the difference in the gaps between the wing/fender and the wheel. Because these vary it often seems that the actual lowering is not like that quoted.
71 = Only for cars with a clamp diameter of 55 mm on the front axle.
72 = Only for cars with a clamp diameter of 50 mm on the front axle.
73 = Rear shock absorbers with eye-mounting.
75 = Vehicles with a two-part leaf spring on the rear axle have to be equipped with a one-piece leaf spring (for Caddy VW part no. for leaf spring spring 2K0511151N for Caddy Maxi VW part no. for leaf spring spring 2K3511151E).
77 = Rear shock absorbers with fork-mounting.
78 = front axle spring perch is height adjustable with the spacer ring
80 = Only for 2- and 3- door versions.
81 = Only for 4 and 5-door vehicles.
85 = Excluding turbo charged petrol engines.
90 = The Front Kit is only to employ with an Rear- Kit.
91 = We recommend a special anti roll bar kit (part no. 68550008) for models with a drive shaft diameter of min. 50mm. This is for improving the clearance of the right hand side drive shaft. Because of car specific differences a clearance is not always given.
92 = Front axle spacers only for cars with 47mm damping tube diameter (OE).
93 = At vehicles with original Nivomat dampers only sport suspension kits can be used. The Nivomat damper will be replaced by the supplied sport damper.
94 = Front axle spacers only for cars with 51mm damping tube diameter (ST suspensions).
96 = Not for cars from 2004 onwards with standard 16“wheels.
97 = Excluding G 40 models.
99 = Please note that the lowering rate quoted in this catalogue will be reduced for models with original sports suspension.
102 = Front spring basis of suspensions and front dampers from modell 2002 have to be replayced by new spring basis Audi part nr. (4D0412107B).
112 = Because of the construction of the car the damping adjustment can only made when the damper is not mounted. By modifying the interior trim this problem can be avoided.
115 = For sport suspension kits with lowering from 45mm please replace the anti-sway bar kit to guarantee enough clearence of the right drive shaft. Anti-sway bar kit for cars without Xenon headlights: part no. 68550006. Anti-sway bar kit for cars with Xenon headlights: part no. 68550007.
120 = On the front axle struts you need to measure the whole distance of the lower mounting drills. This distance has to be 72mm.
121 = Please replace the anti-sway bar kit on max. tested lowering. This is for enough clearance of the right drive shaft. Anti-sway bar kit for cars without Xenon headlights: part no. 68550000. Anti-sway bar kit for cars with Xenon headlights: part no. 68550005.
122 = Models with foglights should have the lightbulbs removed to comply with regulations.
123 = Not for models with special equipement like Camper or Westfalia equipement.
124 = Please use different top mounts for models with a year of construction earlier than 6/92 (BMW part no.: 31336764947; disk 31331116983; nut 31331110196).
128 = Distance between the lower mounting holes of the front dampers should be 52 mm.
130 = Make sure the anti roll bar and the steering arms are at least 5 mm clear of the chassis. If not the chassis should be modified as necessary.
131 = For models with ABS, the ABS-cable needs to be mounted separately.
132 = Rear axle height adjustment is achieved by adjusting the torsion bars.
135 = On the front axle struts you need to measure the whole distance of the lower mounting drills. This distance has to be 58mm.
138 = Excluding Long Wheel Base version.
139 = Only for vehicles up to 2,5l Diesel or Turbo diesel engines.
156 = Only for vehicles with ESP-system.
164 = Rear axle shock absorbers are not atjustalbe for dumping. Sport shock absorbers with a harder dumping characteristic will be supplied.
170 = Only for 4 wheel drive models (4x4, 4motion, Quattro etc.).
181 = Not for vehicles with ESP system.
182 = Only for vehicles where the rear shock absorber is attached at the bottom with an M10 bolt.
183 = Only for vehicles where the rear shock absorber is attached at the bottom with an M14 bolt.
184 = Additional front axle assembly parts for vehicles with EDC and/or 8cyl. engine are required from the automobile manufacturer: for the front: (BMW Part No.: To My. 09/97 = 31 35 2 298 910; Till My. 09/97 = 31 35 2 298 911), for the rear (only sedan): (BMW Teile-Nr. dome bearing 33 521 091 710 + 33 521 090 282 + washer 33 521 092 986 + dust cover 31 331 137 932 + bump stop 33 531 091 031
185 = For the rear axle sport shock absorbers will be supplied, the factory air spring will maintain. The lowering of the vehicle needs to be done according to the instructions.
186 = To guarantee at maximum lowering the minimum clearance of the FA indicator light (350 mm) and day headlight (250 mm) beyond STVZO, they have to be modified
187 = At vehicles equipped with electronic damping DCC, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510141.
188 = At vehicles equipped with audi magnetic ride, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510124.
189 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510144.
190 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510180.
191 = Just for vehicles with air suspension. The vehicle level has to be adjusted at an authorised shop.
192 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510145.
193 = Vehicles with a two-part leaf spring on the rear axle have to be equipped with a one-piece leaf spring. (up to mod.2015; VW part no. for leaf spring spring 2K5511151N; from mod.2015-; VW part no. for leaf spring spring 2K5511151AA)
194 = The indicated lowering rate may vary. Vehicles are factory equipped with spring rubber washers in different heights at the rear axle. The maximal possible lowering is realized by using 5mm spring rubber waschers the rear axle. The lowering rate can by varied by using 5, 9, 13 or 17mm rubber (the rubber washers are only available as original part).
195 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510175 (except OPC) / 68510228 (only OPC).
196 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510213.
197 = VA- Strut with 10mm Bolt.
198 = VA- Strut with 12mm Bolt.
199 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510253.
200 = Only for cars with independent axle (independent wishbone construction)
201 = Only for cars with torsion beam axle (solid axle)
202 = For rear axle camber adjustment we recommend the installation of the car specific adjustable control arm set from KW. KW Part-no. 68510021.
203 = Not for models with complete struts on the rear axle. Only for Cars with separat Springs and Dämpers
204 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510212.
205 = Additional assembly parts from manufacturer required. (Fiat Part No.: support bearing 777 59 40 + sleeve 779 52 59 + washer 779 52 60).
206 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510314.
207 = not for vehicles with Xenon headlights.
207a = suspensions kit is not for vehicles with Xenon headlights. Use our spring sets please.
208 = Additional attachments are required from the automobile manufacturer (for the Fiat Bravo/Brava only available for vehicles with original sport suspension). Fiat Part No.: support bearings 00046469709 + strut insulator 00046448102
209 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510342.
210 = For rear axle camber adjustment we recommend the installation of the car specific adjustable control arm set from KW. KW Part-no. 68510065.
211 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510370.
212 = only for cars without active steering, only cars with a straight front bar, without middle- crank
213 = only for cars with 5-hole-wheel fixation
214 = only for vehicles with roll bar linkage on the front lower control arm
215 = only for cars with 4-hole-wheel fixation
216 = If the car is equipped with PASM, the PASM needs to be disabled.
217 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510148.
218 = For ST XA: Rear axle shocks does not offer hardness adjustment
220 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510426.
221 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510440.
222 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510358
223 = Sway bar link must be changed at cars with a sway bar link longer than 290 mm. Kia part number 54830A 6000
224 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510462
225 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510228
226 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510424
227 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510119
228 = only for cars with damper diameter 50mm (not 48,5mm) / clamp diameter 53mm on the front axle
229 = only for cars with damper diameter 48,5mm (not 50mm) on the front axle
230 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510476
231 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68511059
232 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68510301
233 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68511079.
234 = At vehicles equipped with electronic damping, the electronic damping control needs to be deactivated. Deactivation kit KW Part-no. 68511074.
235 = In combination with coilover suspension kits whose anti-sway bar bracket is placed lower than those of the original suspension, additional coupling rods (part no. 685 11 080) have to be ordered separately.
236 = Front and rear height-adjustable (front and rear springs with height adjustment; usage only with factory dampers)
237 = only for cars with damper diameter 50mm (not 48,5mm) / clamp diameter 53mm on the front axle
238 = only for cars with damper diameter 48,5mm (not 50mm) on the front axle
239 = height adjustability only for front axle (springs + height adjustment), rear axle lowering with standard air suspension
240 = only for vehicles with eye mounting on the front axle
VA = front axle
HA = rear axle
301 = No requirements
302 = Wheel arch needs to be rolled / modified
303 = Wheel arch modification necessary
304 = Wing extensions required, e.g GTi wings
305 = Additional work to the wings required (extended etc.)
306 = Longer studs are required (NOT included to scope of delivery)
Please order seperately.Longer studs are required (NOT included to scope of delivery)
Please order seperately.Longer studs are required (NOT included to scope of delivery)
Please order seperately.
307 = Longer studs need to be pressed in (included in scope of delivery)
308 = Only for rear axle
309 = Not possible for all models! Please check certificate!
310 = Please be careful with fitting. There must be enough centering on the wheel hub (approx 2mm).
311 = NOT in combination with steel wheels
312 = Only for front axle
313 = Chamfer of the rim at least 5x45°, length of wheel hub max. 13,0mm.
314 = Made of steel
315 = Use only with wheel-tire combination that is quoted in the certificate.
316 = Original threaded wheel studs must be shortened by approxemately 12mm. This is the same like the area without thread. Minimum thread engagement is 7.5 turns.
317 = ATTENTION: Installation only with wheels which have cut outs on the rear of the wheel.
318 = If the car is equipped with additional wheel hub caps this caps possibly have to be removed and have to be replaced by other sealing measures. The wheel spacer disc must fit the wheel hub without any play or float.
319 = M14x1.5 bolts must be used to mount the wheel on the AZX-wheel spacer. Seat and shaft length of the bolts must match the actual used wheel bolts. Applies only to system AZX.
320 = ST shaft nuts with a 60° taper seat must be used to mount the wheel. The mounting holes of the wheel must have 60° taper seat, too. Additionally please check before assembly if the shaft of the ST shaft nut fits through the mounting holes of the wheel. ST shaft nuts can only be used in combination with system DZX. ST shaft nuts must be ordered seperately. ATTENTION! Pleases consider minimum thread engagement.
321 = For system AZX ST threaded bolts have to be ordered separately. The thread of the ST threaded bolts has to be similar to the one of the original knurled studs.
322 =
323 =
324 = ATTENTION: M12x1.25 bolts must be used to mount the wheel on the wheel spacer. Seat and shaft length of the bolts must match the actual used wheel bolts.
ABE
 = Vehicle Type Approval: When using the specified tire- / wheel combinations and the standard wheels, a presentation or acceptance by an expert is not necessary. Vehicle Type Approval documents have to be kept in the vehicle. The delivery content includes wheel bolts.
ABE*
 = The proper condition of the vehicle needs to be confirmed by a officially authorized expert or inspector for vehicle traffic or a member of a supervisory organization according to the Road Traffic Licensing Regulations, Section 4 of Appendix VIIIb, stating the vehicle manufacturer, vehicle type and vehicle identification number.
§19.3 = Presentation of the vehicle at an expert. No need to register into vehicle documents.
§21 = For applications which are listed with §21, an individual inspection by an officially recognized expert for motor vehicle traffic is necessary. The acceptance of wheel spacers is made under consideration of the allowed change in spacer width of 2% or 4%.
i.p. = in preparation (parts certificate in preparation, an approval according to §21 is possible).
System
A1/A2		 = For systems A1 and A2 the necessary screws/nuts for fitment of the spacers to the hub are included in delivery. To fix the wheel to the spacer use the original screws/nuts. System A1: Warning! It is absolutely necessary to check that the bolts used are not too long. Before assembly check that the wheel bolts do not protrude beyond the wheel spacer (sample mounting on the rim). System A2: For vehicles with studs, make sure that the original bolts do not extend beyond the wheel spacer, except those used on wheels with corresponding holes. (see pictures Abb. 1/2/3/4)
System
D1/D2/DZ/DZX		 = For systems D1/D2/DZ and DZX longer wheel bolts have to be ordered separately (unless otherwise stated). To order longer wheel bolts the following information is required:
- Thread diameter and pitch (for example M14x1.5)
- Shaft length (thread start to the seat)
- Seat (tapered, rounded, flat, etc.)
- Bolts must be longer according to the wheel spcer thickness
Warning: Wheel bolts that are too long may cause damage at the axle components. When mounting the clearance of the wheel bolts must be checked.
Attention: For applications with ABE longer wheel bolts are included
System D3 = Wheel spacers of the system D3 are delivered with the needed longer wheel bolts.
Certificate No. / Material = homologation documents available on www.st-suspensions.com
10…. Made of Steel
30... , 40... , 50... , Made of Aluminium
Please check homologation certificates for correct fitment, vehicle types and the conditions. Please pay attention to the conditions and comments.